居然会忙到没时间发文。趁礼拜天有空一次po！
首先是 钢普拉 全装甲钢弹KA版 手臂轴关节断裂
https://i.imgur.com/2kAvzP5.jpg
https://i.imgur.com/sG0hIAX.jpg
https://i.imgur.com/T1VFwLM.png
先将断裂的零件取出，扭曲的转轴废弃，重新做一组
https://i.imgur.com/qTNnCUR.jpg
剪取出一节钢弹模型框架，塑胶棒
https://i.imgur.com/WKyrHNi.jpg
转轴用0.7钻尾，钻出两孔
https://i.imgur.com/dGXqhAl.jpg
关节尾端用0.7钻尾，钻出两孔
https://i.imgur.com/rGIDbFw.jpg
https://i.imgur.com/Ht31H0J.jpg
剪取一段白铁线，折出适当形状
https://i.imgur.com/XyB2wsJ.jpg
利用白铁线串联断裂零件
https://i.imgur.com/NogweUb.jpg
尾端反折，维修完毕
https://i.imgur.com/dMUiCAj.jpg
组合
https://i.imgur.com/agDJiMZ.jpg
https://i.imgur.com/Ei7f3cR.jpg
https://i.imgur.com/tIMaihc.jpg
接着是御模道 阿拉克妮02 肩膀关节断裂
https://i.imgur.com/8IzUIWa.jpg
https://i.imgur.com/cvAt3O3.jpg
同色框架补上球关
https://i.imgur.com/xsnPJEA.jpg
圆环上用0.7钻尾，钻两小孔
https://i.imgur.com/o7e8P9n.jpg
两孔之间挖出沟槽线
https://i.imgur.com/pVhmugL.jpg
球型关节上打入两小孔
https://i.imgur.com/ZDcfbRd.jpg
将白铁线折出适当形状， 待插入小孔
https://i.imgur.com/fO6vOCb.jpg
利用白铁线串接断裂零件， 反折固定
https://i.imgur.com/Pu37CgR.jpg
补胶，补色
https://i.imgur.com/mZCq8Pw.jpg
维修完成
https://i.imgur.com/o0qikim.jpg
https://i.imgur.com/24z2cQm.jpg
https://i.imgur.com/onfSPpP.jpg
再来是FGO Avenger/圣女贞德Alter 军旗、枪头连结处断裂
https://i.imgur.com/8x8QMCj.jpg
https://i.imgur.com/321ie7R.jpg
枪头的部分断裂处用1.3钻尾，各钻一个孔
https://i.imgur.com/Qnq2Ugl.jpg
https://i.imgur.com/AQkrth4.jpg
尾端部分打入1.4螺丝
https://i.imgur.com/Irvvrhn.jpg
用手把枪头慢慢扭上去
https://i.imgur.com/nju0jNB.jpg
旗子与披风断裂处的卡榫，用1.3钻尾钻孔
https://i.imgur.com/BF3UQPH.jpg
锁入1.4螺丝
https://i.imgur.com/yQo6MNy.jpg
用尖嘴钳慢慢拔出
https://i.imgur.com/SRwmBjx.jpg
旗子上用1.3钻尾钻孔
https://i.imgur.com/lu4ktxV.jpg
锁上1.4螺丝后用胶水固定
https://i.imgur.com/njuUKJQ.jpg
用尖嘴钳剪断螺丝头后， 将断裂零件结合
https://i.imgur.com/KsWi4lz.jpg
https://i.imgur.com/edNF1Jl.jpg
维修完成，拍几张照片来看看
https://i.imgur.com/9jMpRv6.jpg
https://i.imgur.com/DyVJ8tQ.jpg
https://i.imgur.com/5Yz5YZH.jpg
最后是BC-01断空我 收纳盖补转轴
https://i.imgur.com/DUNpASo.jpg
剪粗一段铁丝，拉直
https://i.imgur.com/I2InEmf.jpg
https://i.imgur.com/Ihzxptx.jpg
涂黑色
https://i.imgur.com/uPRq0g8.jpg
测试松紧度
https://i.imgur.com/2xhXGZy.jpg
剪下适当长度
https://i.imgur.com/pDu0gYA.jpg
维修完成
https://i.imgur.com/q7oNB09.jpg
感谢各位收看