我现在的问题是建立drbd到了两台主机要sudo drbdadm create-md r0 后就卡在那边一点
讯息也没有,我用的是drbd8-utils
server1的hosts设定如下
127.0.0.1 localhost
127.0.1.1 server1.dom23.com server1.dom23.com
::1 ip6-localhost ip6-loopback
fe00::0 ip6-localnet
ff00::0 ip6-mcastprefix
ff02::1 ip6-allnodes
ff02::2 ip6-allrouters
10.120.223.1 server1.dom23.com server1.dom23.com
10.120.223.2 server2.dom23.com server2.dom23.com
server2的hosts设定如下
127.0.0.1 localhost
127.0.1.1 server2.dom23.com server2.dom23.com
::1 ip6-localhost ip6-loopback
fe00::0 ip6-localnet
ff00::0 ip6-mcastprefix
ff02::1 ip6-allnodes
ff02::2 ip6-allrouters
10.120.223.1 server1.dom23.com server1.dom23.com
10.120.223.2 server2.dom23.com server2.dom23.com
在server1的/etc/fstab设定如下
UUID=bf895aa3-5892-4cc7-afd2-3d696716e283 / ext4
errors=remount-ro 0 1
# swap was on /dev/sda5 during installation
UUID=f9953345-5e7d-41a2-a958-41babe1bbe42 none swap sw
0 0/dev/sdb1 /DRBD ext3 defaults 0 0
在server2的/etc/fstab设定如下
UUID=90d60978-95c7-418a-adeb-112f1cd6df33 / ext4
errors=remount-ro 0 1
# swap was on /dev/sda5 during installation
UUID=bc733dc4-f37d-4d0a-80aa-c704163cf5ea none swap sw
0 0
/dev/sdb1 /DRBD ext3 defaults 0 0
server1合server2 /etc/drbd.conf设定如下
global { usage-count no; }
common { syncer { rate 10M; } }
resource r0 {
protocol C;
startup {
wfc-timeout 60;
degr-wfc-timeout 60;
}
net {
cram-hmac-alg sha1;
shared-secret "secret";
}
on server1.dom23.com {
device /dev/drbd0;
disk /dev/sdb1;
address 10.120.223.1:7788;
meta-disk internal;
}
on server2.dom23.com {
device /dev/drbd0;
disk /dev/sdb1;
address 10.120.223.2:7788;
meta-disk internal;
}
}
而server1的主机名称是server1.dom23.com server2的主机名称是server2.dom23.com,
server1的eth0是10.120.223.1 eth1是10.120.230.1 ,server2的eth0是10.120.223.2
eth1是10.120.223.2
,想请问我打sudo drbdadm create-md r0 会完全连个讯息都没有,我看网络上至少都会有
个
Writing meta data...顶多是error掉但我是什么都没有然后按enter选yes会出现下面的
讯息
md_offset 32211202048
al_offset 32211169280
bm_offset 32210186240
Found ext3 filesystem
31456256 kB data area apparently used
31455260 kB left usable by current configuration
Device size would be truncated, which
would corrupt data and result in
'access beyond end of device' errors.
You need to either
* use external meta data (recommended)
* shrink that filesystem first
* zero out the device (destroy the filesystem)
Operation refused.
Command 'drbdmeta 0 v08 /dev/sdb1 internal create-md' terminated with exit
code 40
不知道有没有大大可以帮初学linux指点明路,谢谢~