开箱的是 APS 的 CAM870 胶托版本
不过由于海关的关系箱子残破不堪
在购买当天下雨，所以外和已经被丢了
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0256.jpg
内容物
枪一把，集弹网，说明书，88g CO2一瓶，小钢瓶用的压力瓶，灌气工具
子弹两颗，推弹片，弹壳盖片，橡胶弹5颗，枪托调整用塑胶模组
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0257.jpg
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0258.jpg
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0259.jpg
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0260.jpg
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0261.jpg
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0262.jpg
88g 的钢瓶是没办法直接装到灌气工具上的，还需要再多买一个转接头(选购)
所以真不知道他在盒子内附赠这灌CO2是做啥用的........
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0263.jpg
小钢瓶用的
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0264.jpg
将小钢瓶屁股相靠放入瓶中
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0265.jpg
把第一层锁紧后 才将后面刺破用的锁紧刺破钢瓶
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0266.jpg
弹壳是可拆式
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0268.jpg
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0269.jpg
灌气时先将后面的手把锁紧将弹壳往下推，打开气阀后锁紧气阀在将弹壳向上推即可
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0270.jpg
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0271.jpg
子弹装填
灌好气后先放入推片
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0272.jpg
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0273.jpg
再放入BB弹或者任何你想射出去的东西，只要是枪管能通过的东西都能射
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0274.jpg
盖上弹壳盖片
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0275.jpg
又或者单放一颗橡胶弹
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0277.jpg
装填子弹的顺序
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0278.jpg
装填子弹处
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0279.jpg
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0280.jpg
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0281.jpg
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0282.jpg
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0283.jpg
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0284.jpg
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0285.jpg
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0286.jpg
在护木上加装鱼骨
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0287.jpg
护木和枪管的空隙很大，除非螺丝太长不用担心会刮到枪管
装上枪灯
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0231.jpg
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0232.jpg
上膛未击发要退弹的按钮
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0288.jpg
保险
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0289.jpg
弹仓和枪身连接处
枪管和弹仓全靠这4颗螺丝和枪身连接，所以操作上不要太粗暴
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0292.jpg
装上集弹网
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0290.jpg
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0291.jpg
拆护木专用的工具
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0293.jpg
黑色的是买来的工具一个300元，材质是塑胶
左是五金行买的6分水管接头，自行制作的护木拆解工具，一个9元......|||
自行制作的只有外观不好看而已使用上完全没问题
附上自行录制的 拆解说明
https://youtu.be/jB9bOnsQEKg
用内视镜拍摄枪管内枪机做动及上退弹
https://youtu.be/oSVFXvjSPtU
最后再来个自行制作的枪架配上照明~
http://i204.photobucket.com/albums/bb266/tkfs1/ATXA/DSC_0238.jpg